PCB design anti-interference measures

In electronic system design, in order to reduce detours and save time, interference resistance requirements should be fully considered and met, and interference remediation should be avoided after the design is completed. There are three basic elements that form interference:

(1) Interference source, refers to the interference components, equipment or signals, described in mathematical language as follows: du / dt, di / dt large place is the interference source. For example, lightning, relays, controllable silicon, motors, high-frequency clocks, etc. can be a source of interference.

(2) Propagation path refers to the pathway or medium through which interference propagates from the interference source to the sensitive device. A typical interference transmission path is through conduction through wires and radiation from space.

(3) Sensitive devices refer to objects that are easily interfered with. Such as: A / D, D / A converter, MCU, digital IC, weak signal amplifier and so on. The basic principles of anti-interference design are to inhibit the interference source, cut off the interferences propagation path, and improve the anti-interferences performance of sensitive devices.

1 Suppress the interference source

The suppression of interference sources is to reduce the du / dt, di / dt of the interference source as much as possible. This is a good first consideration and important principle in anti-interference design, which often results in more than one effort. Reducing the du / dt of the interference source is mainly achieved by shunt capacitors at both ends of the interference source. Reducing the DI / DT of the interference source is achieved by connecting the inductance or resistance in the interference source loop and adding the freewheeling diode.

Common measures to suppress interference sources are as follows:

(1) Add freewheeling diodes to the coil of relay to eliminate the counter electromotive force when the coil is broken. Adding a continuing flow diode only will delay the disconnection time of the relay, and the relay can move more times per unit time after adding a steady pressure diode.

(2) At both ends of the relay contact and connect the spark suppression circuit (generally RC serial circuit, the resistance is generally selected from several K to dozens of K, and the capacitance is selected from 0.01uF) to reduce the impact of spark.

(3) Add a filtering circuit to the motor, and pay attention to the capacitance and inductor lines to be as short as possible.

(4) Each IC on the circuit board should be connected in parallel with a 0.01μF ~ 0.1μF high-frequency capacitor to reduce the impact of IC on the supply. Pay attention to the wiring of high frequency capacitors. The wiring should be close to the power end and as short as possible, otherwise, it increases the equivalent serial resistance of the capacitor and will affect the filtering effect.

(5) Avoid 90 degree cuts when wiring to reduce high frequency noise emission.

(6) Both ends of the controllable silicon are connected to the RC suppression circuit to reduce the noise generated by the controllable silicon (this noise may break the controllable silicon when it is serious).

According to the propagation path of the interference, it can be divided into two categories: conduction interference and radiation interference.

The so-called conduction interference refers to interference that propagates through a wire to a sensitive device. High-frequency interference noise differs from the frequency band of useful signals, and the propagation of high-frequency disturbance noise can be interrupted by adding filters to the conductor, and sometimes isolated photocouples can be solved. Power supply noise is very harmful, and special attention should be paid to its treatment. Radiation interference refers to interference transmitted to sensitive devices through space radiation. The general solution is to increase the distance between the interference source and the sensitive device, isolate them by a landline and shield the sensitive devices.

2 Common measures to cut off interference propagation paths are as follows:

(1) Consider fully the impact of the power supply on the microcontroller. The power supply is well done, and the interference resistance of the entire circuit is solved by more than half. Many microcontrollers are sensitive to power noise, and you should add a filter circuit or voltage stabilizer to the motherboard power to reduce the interference of power noise on the microcontroller.For example, it is possible to use magnetic beads and capacitance to form a π-shaped filter circuit, but when the conditions are not high, it is also possible to replace the magnetic beams with a 100Ω resistor.

(2) If the I / O port of the single-chip microcomputer is used to control noise devices such as motors, isolation should be added between the I / O port and the noise source (increase the π-shaped filter circuit).Noise devices such as control motors should be isolated between the I / O port and the noise source (increase the π-shaped filter circuit).

(3) Pay attention to the transistor wiring. The transistor and the microcontroller pins are as close as possible, the ground line separates the clock area, and the transistor casing is grounded and fixed. Such a measure could solve many difficult problems.

(4) Reasonable partition of circuit board, such as strong, weak, digital, analog signal. Keep the sources of interference (e.g. motors, relays) and sensitive components (e. g. microcontrollers) away as far as possible.

(5) The landline separates the digital area from the analog area, and the digital area and the analog area must be separated and connected to the power source at a point. A / D, D / A chip wiring also takes this as a principle, and manufacturers have considered this requirement when allocating A / D and D / A chip pin arrangement.

(6) The ground lines of the microcontroller and high power devices should be separately grounded to reduce interference with each other. High-power devices are placed at the edge of the board whenever possible.

(7) using anti - jamming components such as magnetic beads, magnetic rings, power filters and shielding covers in the key places such as singlechip i / o ports, power lines and circuit board connections, can improve the anti - jamming performance of the circuit remarkably.

3 Improve the interference resistance of sensitive devices

Improving the anti-interference performance of sensitive devices refers to considering ways from the sensitive device to minimize the picking up of interference noise and recover from an abnormal state as soon as possible.

Common measures to improve the interference resistance of sensitive devices are as follows:

(1) When wiring, the area of the circuit ring is minimized to reduce the induction noise.

(2) When wiring, the power line and ground line should be as thick as possible. In addition to reducing pressure reduction, it is more important to reduce coupling noise.

(3) For the idle I / O port of the MCU, do not dangle, and must be grounded or connected to the power supply. The idle end of the other IC is grounded or connected to the power supply without changing the system logic.

(4) The use of power monitoring and watchdog circuits on the MCU, such as: IMP809, IMP706, IMP813, X25043, X25045, etc., can greatly improve the anti-interference performance of the entire circuit.

(5) To the extent that the speed can meet the requirements, minimize the wafer of the microcontroller and choose a low-speed digital circuit.

(6) IC components as far as possible directly welded to the circuit board, less use of IC block.

In order to achieve good anti-interference, so we often see the PCB board has a divided wiring. However, not all digital circuits and analog circuits mixing must be ground level segmentation. Because this division is designed to reduce noise interference.


Name:
Message:
Verification code:
Submit
Comment
Telephone consultation:+8615354810295
QQ consultation:3040308863
WeChat customer service
Scan the QR code for consultation